Re: Teacup on Sanginololu under Win 7
Glad that fancy piece of paper left me with some deductive skills and a little feeling for error messages. :) Two out of four likely candidates do, in fact, have a parallel port. I can load whatever...
View ArticleRe: Teacup on Sanginololu under Win 7
QuoteOSUFlatlandI know they bought Atmel a while back, but have no idea how compatible the interfaces are. This one likely works. AFAIK there is only one such device for the whole AVR range....
View ArticleRe: Teacup on Sanginololu under Win 7
It occurs to me that the ISP may be doubling for the display header. Pretty sure one of the pin clusters it's plugged into is a 2x3. I'll check it out when I get home tonight or tomorrow and report...
View ArticleRe: Teacup on Sanginololu under Win 7
QuoteOSUFlatlandIt occurs to me that the ISP may be doubling for the display header. Yes, the programming header is actually an SPI header with Chip Select connected to Reset. Displays connecting to...
View ArticleRe: Teacup on Sanginololu under Win 7
Can do. Hopefully I can get to it tomorrow after work, but no promises. 12 hour shifts eat your work days. :)
View ArticleRe: Teacup on Sanginololu under Win 7
So...I have a bunch of Pro Micro's, which the how-to seems to say won't work because they don't have an FTDI chip - on chip USB - or a couple Mini Pro, which use an off board FTDI USB-TTL programmer.I...
View ArticleRe: Teacup on Sanginololu under Win 7
Try them. Once there's a bootloader on the chip three's no need to ever look back.
View ArticleRe: Teacup on Sanginololu under Win 7
Update:the Pro Micro seems to have taken the Arduino ISP code, but I need a cable now, and would like something a bit more elegant than bits of CAT5 stuck to a few strips of 1x header strip. I'll try...
View ArticleRe: Teacup on Sanginololu under Win 7
Attempting to use a Pro Micro to burn the bootloader to the Sanguinololu gives me the following: Arduino: 1.6.4 (Windows 7), Board: "Sanguino, ATmega1284 or ATmega1284P (16 MHz)" C:\Program Files...
View ArticleRe: Teacup on Sanginololu under Win 7
QuoteOSUFlatlandUsing Programmer : stk500v1 Given that your programmer should support binaries > 64 kB, this might not work. Swapping stk500v1 for stk500v2 (-c parameter) should give better...
View ArticleRe: Teacup on Sanginololu under Win 7
Okay, solved a driver issue with the Arduino, which I probably should have done before even trying, but I was impatient... Same error. Do I have to try burning the boot loader from a command line or...
View ArticleRe: Teacup on Sanginololu under Win 7
I also tried uploading with "Arduino as ISP" as the programmer, and received the following: Arduino: 1.6.4 (Windows 7), Board: "Sanguino, ATmega1284 or ATmega1284P (16 MHz)" C:\Program Files...
View ArticleRe: Teacup on Sanginololu under Win 7
Also, I tried AVRISP Mk II, but it gave the error "could not find usb" or somesuch - I assume because that programmer does not operate over a simple COM port.
View ArticleRe: Teacup on Sanginololu under Win 7
Using the command line is much easier in such cases. Still some people prefer to edit the boards.txt file somewhere inside the Arduino folder to adjust parameters there. In case you want to access the...
View ArticleRe: Teacup on Sanginololu under Win 7
I you're trying to use an FTDI connection, you are basically trying to program the AVR thought the serial interface. I'm not 100% sure of this, but I think in this case, you need a bootloader on your...
View ArticleRe: Teacup on Sanginololu under Win 7
I'm using a Pro Micro clone, based on a 16u4 with USB on chip. I've been trying to read up on this, but depending on what you meant, most sources aren't very forthcoming on the "how" as much as the...
View ArticleRe: Teacup on Sanginololu under Win 7
QuoteOSUFlatlandWindows is far more user friendly in day to day use. This is something I read often, and which is hard to believe to me. Recently I set up XP just for testing Configtool and I found a...
View ArticleRe: Teacup on Sanginololu under Win 7
If you don't code much, package dependencies are usually included in win installers. I believe your complaint is with poor ports. :-) Using avrdude in command line I get the following while trying to...
View ArticleRe: Teacup on Sanginololu under Win 7
Those messages mean to me that you're not even connecting to the processor. Either your baud rate is wrong or your port is wrong. Or your programmer is wrong.
View ArticleRe: Teacup on Sanginololu under Win 7
Hmm. Good news and bad news. I tried reinstalling the ArduinoISP firmware to my Pro Micro and now it shows up as "Unknown Device" and I can't even pull a device ID from it. The good news being...
View Article